do not scale from this print designed & dimensioned in millimeters [inches] tem-1xx-xx-xx.x-xx-d-xx-xx no of positions -05 thru -50 (per row) (5 pos increments) row specification -d: double row lead style -02: surface mount plating specification -h: heavy, .000030 gold on post, gold flash on tail -g: gold, .000010 gold on post gold flash on tail -fg: flash, .000003 gold on entire terminal option -tr: tape & reel -k: polyimide film (use k-500-300, see fig. 5, sht 2) option -a: alignment pin (see fig. 2, sheet 2) (not available with -lc or -wt) -lc: locking clip (see fig. 3, sheet 2) (not available with -a or -wt) -wt: weld tab (see fig. 4, sheet 2) (not available with -a or -lc) stack height -03.0: (6mm stack height) (t-1m58-03.0-xx) -04.0: (7mm stack height) (t-1m58-04.0-xx) -07.0: (10mm stack height) (t-1m58-07.0-xx) (no. of pos x 0.800[.0315]) + 9.000[.3543] ref (no. of pos x 0.800) + 5.000 ref .196 3.50 .138 ref 5.00 .197 ref 0.25 .010 ref ref "d" "b" "a" ref 5.45 .215 ref (see note 5) 0.86 .034 ref (see note 5) 3.05 .120 ref (see note 5) 1.04 .041 ref (see note 5) (no. of pos -1) x 0.800 0.130 .0315 .005 (no. of pos -1) x 0.800 0.130 .0315 .005 2 max sway (typ) "a" "a" c c c c 01 02 first position indicator 0.10 [.004] slot (see notes 5 & 6) 0.315 ref .012 5.50 .217 1.600 .063 2 max toe (typ) section "a"-"a" tem-xx-xx.x t-1m58-xx.x-xx c c c fig. 1 (tem-110-02-03.0-xx-d shown) h sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles x.x: 0.3 [.01] 2 x.xx: 0.13 [.005] x.xxx: 0.051 [.0020] material: .8mm tiger eye micro terminal by: tem-1xx-xx-xx.x-xx-d-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b ray 10-18-2007 2 1 sheet scale: 4:1 insulator: zenite ze55201, color: black terminal and locking clip: phos bronze 510 weld tab: brass alloy 260, full hard f:\dwg\misc\mktg\tem-1xx-xx-xx.x-xx-d-xx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum pushout force for terminal, locking clip and weld tab: 2.22n [0.50lbf]. 3. post height variation between any two pins: 0.13 [.005] maximum. 4. parts to be packaged in trays unless otherwise specified. 5. positions -05 thru -20 will have only one slot per side. positions -25 thru -40 will have two slots per side. positions -45 thru -50 will have three slots per side. 6. slots only available in -03.0 lead style. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision h
1.25 ref .049 0.90 ref .035 0.75 ref .030 "s" (see note) "r" (see note) 5.50 0.13 .217 .005 0.25 .010 note: "r" = overall length (ref) "s" = {("r" - 5.50[.216])/2[.0787]} 0.51[.020] "c" (see table 1) 1.00 .039 ref (no of pos x 0.800[.0315]) + 2.000 .079 ref tem-xx-xx.x-a 0.25 .010 ref 1.27 .050 (no of pos x 0.80[.031]) + 7.00[.276] 2 max sway (typ) c c lc-06-tm tem-xx-xx.x-lc 0.30 .012 ref + 7.00[.276] (no of pos x 0.80[.031]) 2 max sway (typ) "b" "b" c tem-xx-xx.x 0.50 .020 ref 1.84 .072 section "b"-"b" c wt-36-xx-t fig. 2 (tem-110-02-03.0-xx-d-a shown) (same as fig. 1, different as shown) fig. 3 (tem-110-02-03.0-xx-d-lc shown) (same as fig. 1, different as shown) fig. 4 (tem-110-02-03.0-xx-d-wt shown) (same as fig. 1, different as shown) fig. 5 (tem-110-02-03.0-xx-d-k shown) (same as fig. 1, different as shown) h table 2 stack height weld tab -03.0 wt-36-02-x -04.0 wt-36-03-x -07.0 wt-36-04-x sheet of .8mm tiger eye micro terminal by: tem-1xx-xx-xx.x-xx-d-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b ray 10-18-2007 2 2 sheet scale: 3:1 revision h f:\dwg\misc\mktg\tem-1xx-xx-xx.x-xx-d-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
